BMWSportTouring BMWST DB
Previous Thread
Next Thread
Print Thread
#1002495 - 12/19/17 02:39 AM Wiring an aftermarket horn  
Joined: Feb 2009
Posts: 632
cris nitro Offline
Member
cris nitro  Offline
Member

Joined: Feb 2009
Posts: 632
Chatham, Va.
Evening.
I just installed a Denali Sound Bomb air horn on my 2010 RT. A bit of a pain mounting and working with the short wires to the stock horn, but I got it. It came with a relay which required an input with a 30A fuse connected to the battery. The relay also picked up the original horn trigger positive and negative. Instead of taking the power directly off the battery, I connected it to one of the switched blocks on on Fuze Bloke. It worked well until I started the bike and tried the horn and it blew the 10A fuse in my Fuze Block. Should I connect it directly to the battery per the directions? And if so, with it being direct to the battery, will it draw down any power when not in use?
Thank you and I hope everyone here has a Merry Christmas.


2011 Suzuki DL650A V-Strom
2010 1200RT Polar Metallic
2006 Buell Blast
2017 KTM 250 XCW

Many, many more, all gone...
#1002511 - 12/19/17 02:53 PM Re: Wiring an aftermarket horn [Re: cris nitro]  
Joined: Apr 2006
Posts: 796
duckbubbles Offline
Member
duckbubbles  Offline
Member

Joined: Apr 2006
Posts: 796
Austin, Texas, USA
I ran positive and negative directly from the battery to the relay and used the original horn wires to trigger the relay on a Stebel Nautilus air horn. Zero battery draw until you actuate the horn button. I think it is a 10A fuse that has never blown.

Frank


2017 R1200RS, 7 mo. 10,000 mi.
2003 R1100S Boxer Cup Replika #6/200
2016 R1200RS, 18 mo. 28,322 mi. (gone)
1985 K100/1100RS, 32 yrs. 326,000 mi.
2005 R1200ST 8 yrs.(gone)
2011 R1200RT 2 yrs. (gone)
#1002526 - 12/19/17 07:09 PM Re: Wiring an aftermarket horn [Re: duckbubbles]  
Joined: Feb 2009
Posts: 632
cris nitro Offline
Member
cris nitro  Offline
Member

Joined: Feb 2009
Posts: 632
Chatham, Va.
Originally Posted by duckbubbles
I ran positive and negative directly from the battery to the relay and used the original horn wires to trigger the relay on a Stebel Nautilus air horn. Zero battery draw until you actuate the horn button. I think it is a 10A fuse that has never blown.

Frank


Thank you.


2011 Suzuki DL650A V-Strom
2010 1200RT Polar Metallic
2006 Buell Blast
2017 KTM 250 XCW

Many, many more, all gone...
#1002804 - 12/28/17 03:16 AM Re: Wiring an aftermarket horn [Re: cris nitro]  
Joined: Mar 2005
Posts: 589
AZgman Offline
Member
AZgman  Offline
Member

Joined: Mar 2005
Posts: 589
AZ
Your horn should have an amp rating listed on it. It could be as high as 15 amps!


2017 R1200GS
#1002806 - 12/28/17 03:46 AM Re: Wiring an aftermarket horn [Re: AZgman]  
Joined: Oct 2000
Posts: 1,204
Paul De Offline
Member
Paul De  Offline
Member

Joined: Oct 2000
Posts: 1,204
Milwaukee Wisconsin, USA
Originally Posted by AZgman
Your horn should have an amp rating listed on it. It could be as high as 15 amps!


When looking at the specification it will be listed as something like Absorbed Current which is used for electric motors. Long and short of it there will be a surge current to spin up the compressor motor which might be closer to 20 Amps and then current draw will settle some and 15 amps is probably about high side right. I used a HEX ezCAN and put the horn on a high current 30 Amp circuit to integrate with strobing the driving lights when the horn is activated. Low cost approach is to use the 30 AMP relay and connect the horn wires to the trigger tabs and the high current side to the battery.

Nice install video here
https://www.youtube.com/watch?v=ODRg97aWrVY


If the good old days were so damn good, why did we bother to invent modern times?

Most missed bike: Bultaco Sherpa T 326
#1002809 - 12/28/17 10:42 AM Re: Wiring an aftermarket horn [Re: cris nitro]  
Joined: Jun 2010
Posts: 13,705
dirtrider Offline
The Oracle
dirtrider  Offline
The Oracle
Member

Joined: Jun 2010
Posts: 13,705
Ohio
Originally Posted by cris nitro
Evening.
I just installed a Denali Sound Bomb air horn on my 2010 RT. A bit of a pain mounting and working with the short wires to the stock horn, but I got it. It came with a relay which required an input with a 30A fuse connected to the battery. The relay also picked up the original horn trigger positive and negative. Instead of taking the power directly off the battery, I connected it to one of the switched blocks on on Fuze Bloke. It worked well until I started the bike and tried the horn and it blew the 10A fuse in my Fuze Block. Should I connect it directly to the battery per the directions? And if so, with it being direct to the battery, will it draw down any power when not in use?
Thank you and I hope everyone here has a Merry Christmas.



Morning Cris

The SoundBomb Compact draws 20 amps, the SoundBomb Split draws 20 amps, the SoundBomb Mini (no pump) draws 5 amps.

Add a little extra for low voltage amp increase & startup so you will need at least a 25 amp & preferred 30 amp power-supply-side circuit (including proper wire size for run length).

If your add-on fuse block has a 30 amp capable tap (doubtful) then you can use that but the safe way is to run the power-supply-side of your horn relay to battery (+ post) & run the horn motor low direct to battery (- post). Just be sure to use a 30 amp fuse in the (+) side circuit.

If you are JUST powering the horn relay horn-power-supply-side direct from battery then it will NOT draw power unless the horn is actually sounding as the relay is OFF (open) until you push the horn button to energize it.


D.R. ___
Sent from my rotory dial wall phone!
#1003213 - 01/05/18 03:34 PM Re: Wiring an aftermarket horn [Re: cris nitro]  
Joined: Feb 2009
Posts: 632
cris nitro Offline
Member
cris nitro  Offline
Member

Joined: Feb 2009
Posts: 632
Chatham, Va.
Thank you all, got it working well. Took power directly off battery to relay and it works well.


2011 Suzuki DL650A V-Strom
2010 1200RT Polar Metallic
2006 Buell Blast
2017 KTM 250 XCW

Many, many more, all gone...

Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.009s Queries: 14 (0.002s) Memory: 2.7665 MB (Peak: 2.9296 MB) Zlib enabled. Server Time: 2018-04-24 06:51:25 UTC