BMWSportTouring BMWST DB
Previous Thread
Next Thread
Print Thread
#907372 - 10/07/14 11:33 AM BMW R1200RT (Hexhead) Rear Brake Rotor Replacement  

**DONOTDELETE**
Unregistered
Kakugo
Unregistered


Replacing your R1200RT rear brake rotor.

Tools and parts you are going to need:

Rear rotor
Rear brake pads
Torque wrench (19-60Nm range needed)
Heat gun
Brake cleaner
Hammer & punch
Pliers
Large Screwdriver
Ratchet with following bits:
M15
T50
T45
T40, the longer, the better; the higher quality, the better
5 X BMW supplied bolts, code 33177709205 *
Disposable gloves
Marker

Tools and parts you'd better have available:

Thread locker (heat resistant) *
Brake grease
Open ended M11 spanner
Dremel or similar tool with polishing wheel
Q-Tips

*Please note that BMW recommends replacing brake rotor bolts due to them being "microincapsulated" with thread locker at the factory. You can still reuse your original bolts by cleaning them thoroughly and applying a heat resistant thread locking compound.

Start by putting your bike in gear and removing the side cases.



Loosen the M15 nut on the Torca clamp holding the silencer.



Remove the the T45 bolt holding the silencer to the bracket and rotate the silencer to the front of the bike in clockwise fashion.



Put the bike in gear and remove the rear wheel by loosening the five T50 bolts.



Remove the safety pin on the brake pad pin, then use the hammer and punch to remove the pin.

Remove the two T45 bolts holding the rear brake caliper carrier and remove the rear caliper as a whole. Remove the brake pads.



Align the first rotor bolt to the hole on the bottom of the final drive housing.
Use the heat gun to heat the bolt on the carrier side. Remove the T40 rotor bolt.
Caution! If you feel the bolt is putting on some resistance, immediately cease undoing it and apply more heat. The bolt should come loose with loud clank but with minimal effort.



Repeat the two previous steps for all five rotor bolts.
Remove the old rotor.

Before proceeding any further, check your brake rotor carrier for cracks. If you spot any, contact your BMW dealer as soon as possible.



Take the occasion the clean the whole area with brake disc cleaner. Use as much as you need.



Before installing the new brake rotor, clean it with a generous amount of brake cleaner.



Put on the new rotor and put all the brand new 33177709205 bolts in “finger tight” to align the rotor. If you chose to reuse the old bolts (please read the disclaimer above), use a good quality, heat resistant thread locker before installing them.

Once you have aligned the rotor, tighten the bolts: torque is 30Nm. Use the marker to mark bolts as you torque them. And then double check you torqued them all to specs.



Clean the caliper with brake cleaner and install the new brake pads. If you want, you may apply a dab of brake grease to the pin. Put in the pin “finger tight”.

Now, the following step is very important: if even after pushing the caliper pistons all the way in you cannot slide the caliper on the rotor, chances are the front sliding pin on your caliper is rusted and doesn't slide properly, if at all.
At this point, remove the pads and pin and locate the M11 bolt under the caliper. Using the M11 open ended spanner, undo it all the way and separate the caliper from the carrier. If the sliding pin is very rusted, you may need a lot of time to do so.
Clean the hole in the carrier with copious amounts of brake cleaner and the Q-Tips.
Use your Dremel or similar tool to polish the sliding pin as much as possible. Allow it to cool down and clean it throughly with brake cleaner. After the part is dry, apply a small dab (a teardrop, really) of brake grease to the pin.
Reassemble the brake caliper and carrier, install the brake pads and pin and try putting the caliper on the rotor. If it slides properly in, all's good, otherwise chances are you put too much grease on the pin. **

Once the caliper is in place, install the two T45 bolts and torque them to 24Nm.
Using the hammer and punch, drive the pin in place and put the retaining pin in place.
Pump your rear brake pedal thoroughly. We are almost finished now.



Install the rear wheel by aligning it and putting the five T50 bolts in finger tight. Then torque them in criss-cross fashion at 60Nm.



Rotate the silencer backwards in counterclockwise fashion and install the T45 bolt on the bracket. Torque it to 19Nm.



Align the Torca clamp and tighten the bolt at 55Nm.



Reinstall side cases... and you are done.
Be careful with braking for the first few miles, then you can treat the whole assembly as a brand new set of brake pads.

** BMW and Brembo supply only a few spare parts for the caliper, none of which goes any way towards fixing this issue. If at next rear pad change you discover the pin has rusted again, you should consider replacing the whole caliper assembly.
BMW wants well over $600 for it, but you could get lucky with parts from a breaker's. This particular rear brake caliper is used on all Hexhead and Camhead models bar the R1200S: R1200GS, R1200RT, R1200GS-A, R1200R and R1200ST.

#908929 - 10/21/14 01:13 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: ]  
Joined: Nov 2002
Posts: 1,030
lkchris Offline
Member
lkchris  Offline
Member

Joined: Nov 2002
Posts: 1,030
NM USA
Just a couple "technical" comments ...

Metric hex nuts are sized by the diameter of the bolt that passes through them, NOT the size of the wrench required.

The nut on the torca clamp is M8.

In addition the clamp is different on Camheads, and there are in fact two TORX screws.

Likewise, metric screws and bolts are described by their shaft diameter and NOT the wrench size or type, and, for example, the wheel bolts are M10 and NOT T50.

Professional technical writing almost never provides wrench sizes, assuming the mechanic has a full set of tools. A wrench size table would be one thing to provide.

Still a nice write up with great illustrations and I'm probably overly picky.

Last edited by lkchris; 10/21/14 01:14 AM.

Kent Christensen
Albuquerque
'12 R1200RT, '02 R1100S, '84 R80G/S
#908933 - 10/21/14 01:57 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: lkchris]  
Joined: Jan 2010
Posts: 62
wvpc Offline
Member
wvpc  Offline
Member

Joined: Jan 2010
Posts: 62
Ypsilanti, Michigan USA
Kakugo,

Thank you for the nice DIY rear rotor replacement write-up. I noticed your rotor looked to be in good condition. If it was out of spec, how many kms did you have on it? Why did you replace it?


83 Magenta Red Metallic R100 RT and 2012 Midnight Blue Metallic R1200 RT
#909317 - 10/24/14 09:57 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: wvpc]  

**DONOTDELETE**
Unregistered
Kakugo
Unregistered


Originally Posted By: wvpc
Kakugo,

Thank you for the nice DIY rear rotor replacement write-up. I noticed your rotor looked to be in good condition. If it was out of spec, how many kms did you have on it? Why did you replace it?


Yes, it was out of spec. 90000km or so.

I noticed my rear brake was "slipping" under heavy breaking, so checked the rotor with an internal micrometer and found it was replacement time.

#909318 - 10/24/14 10:02 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: lkchris]  

**DONOTDELETE**
Unregistered
Kakugo
Unregistered


Originally Posted By: lkchris
Just a couple "technical" comments ...

Metric hex nuts are sized by the diameter of the bolt that passes through them, NOT the size of the wrench required.

The nut on the torca clamp is M8.

In addition the clamp is different on Camheads, and there are in fact two TORX screws.

Likewise, metric screws and bolts are described by their shaft diameter and NOT the wrench size or type, and, for example, the wheel bolts are M10 and NOT T50.

Professional technical writing almost never provides wrench sizes, assuming the mechanic has a full set of tools. A wrench size table would be one thing to provide.

Still a nice write up with great illustrations and I'm probably overly picky.


Around here we always refer to tool (head) size, bolt size is only used when buying hardware.

Often I forget different places use different conventions: for example Torx heads here are often referred to as French heads, especially by old hands... never mind the fact they were invented by Textron!

#949821 - 12/22/15 12:33 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: ]  
Joined: May 2014
Posts: 7
bobwhi Offline
Just Joined
bobwhi  Offline
Just Joined

Joined: May 2014
Posts: 7
How deep is tire cut ??? To cords ???

#949822 - 12/22/15 12:37 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: ]  
Joined: May 2014
Posts: 7
bobwhi Offline
Just Joined
bobwhi  Offline
Just Joined

Joined: May 2014
Posts: 7
I need seals for 07R1200RT rear master cyclinder... Avail'bl ???

#949826 - 12/22/15 01:13 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: ]  
Joined: Nov 2005
Posts: 3,503
lawnchairboy Offline
Snuggie Jesus
lawnchairboy  Offline
Snuggie Jesus
Member

Joined: Nov 2005
Posts: 3,503
Traffic hell, VA
What is minimum rotor thickness spec?


06 R12RT (for sale) 11 R12GS (for sale) 11 KTM990 ADV

The focus is sharp in the city.
#949840 - 12/22/15 04:16 AM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: lawnchairboy]  
Joined: May 2011
Posts: 1,232
lkraus Offline
Member
lkraus  Offline
Member

Joined: May 2011
Posts: 1,232
Central Ohio
2005-2013

Front thickness new 4.5mm minimum 4.0mm
Rear disc thickness new 5.0mm minimum 4.5mm


Larry
2006 R1200RT
#950307 - 12/30/15 05:35 PM Re: BMW R1200RT (Hexhead) Rear Brake Rotor Replacement [Re: lkraus]  
Joined: Nov 2005
Posts: 3,503
lawnchairboy Offline
Snuggie Jesus
lawnchairboy  Offline
Snuggie Jesus
Member

Joined: Nov 2005
Posts: 3,503
Traffic hell, VA
Thanks. Got another job...


06 R12RT (for sale) 11 R12GS (for sale) 11 KTM990 ADV

The focus is sharp in the city.

Moderated by  EffBee 

Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.009s Queries: 14 (0.002s) Memory: 2.7927 MB (Peak: 2.9754 MB) Zlib enabled. Server Time: 2017-11-23 04:07:17 UTC